Fish Finder

How to Clean Lowrance Fish Finder Screen: Expert Tips & Techniques

Why Lowrance Screens Need Specialized Care

You just pulled your boat out after a long day on the water. The sun is dropping, and you glance at your Lowrance unit — it’s covered in salt spray, smudges from wet fingers, and a few water spots that dried before you could wipe them off. You grab a paper towel and some glass cleaner from the truck, ready to make it look new again. Stop right there.

That paper towel and glass cleaner combo is one of the fastest ways to ruin a perfectly good fish finder screen. Lowrance units use a special anti-reflective coating on the display. Ammonia-based cleaners and abrasive cloths strip that coating over time, leaving you with a cloudy, blotchy screen that’s hard to read in direct sunlight. Once it’s gone, you can’t put it back.

T-H Marine

T-H Marine Wave Away Sonar & GPS Screen Cleaner Kit – Ammonia-Free LCD Screen Cleaner with Microfiber Cloth – Drip-Resistant, Streak-Free Solution for Electronics & Sunglasses – 1.5oz

  • CRYSTAL CLEAR DISPLAY - Experience a streak-free finish on all your devices with our specially formulated LCD screen cleaner, desi…
  • SAFE FOR EVERY SCREEN - Our ammonia-free formula guarantees no damage or scratches on your delicate electronics, including GPS sys…
  • DRIP-RESISTANT DESIGN - Thanks to our innovative drip-resistant technology, Wave Away stays where you spray, minimizing the risk o…

This guide walks you through the right way to clean your Lowrance fish finder screen — the tools to use, the steps to follow, the mistakes to avoid, and how to handle scratches and calibration issues. You’ll also get a seasonal maintenance checklist so your unit stays readable for years, not just until the next trip.

If you want a dedicated cleaning kit that’s safe for your Lowrance, the T-H Marine Wave Away Sonar & GPS Screen Cleaner Kit is a solid option. It’s ammonia-free, so it won’t harm that delicate coating, and it comes with a microfiber cloth that’s perfect for the job. The drip-resistant spray helps you avoid getting liquid into the seams around the screen, which is a common cause of internal damage.

What NOT to Do (The Damage Checklist)

Before we get into the right way, let’s talk about the wrong ways. I’ve seen too many screens ruined by well-meaning anglers using the wrong products. Here’s what to avoid.

The Ammonia and Alcohol Trap

Ammonia is the big one. It’s in most household glass cleaners like Windex. Ammonia breaks down the anti-reflective coating on Lowrance screens, leaving permanent cloudy streaks that make the display hard to read. Alcohol is almost as bad — it can dry out the plastic bezel and cause it to crack over time.

Check the label on any cleaner before you use it on your fish finder. If you see ammonia, alcohol, or any kind of solvent, put it back. Even some “electronics-safe” wipes contain alcohol, so read the fine print.

Why Paper Towels Are Your Enemy

Paper towels feel soft, but they’re actually abrasive. Under a microscope, paper towel fibers are rough and can leave micro-scratches on the screen. Those tiny scratches scatter light, making the display harder to read in bright conditions. The same goes for rough rags, shop towels, or your t-shirt.

See also  The Secret to Finding the Best Transducer for Bass Fishing Revealed

What you want is a clean, soft microfiber cloth. Not the kind you use to dry the boat — a dedicated one for electronics. The T-H Marine kit includes a 12″ x 12″ microfiber cloth that’s made for this purpose, and it comes with a velvet bag so you can keep it clean in your tackle box.

The Ultimate Step-by-Step Cleaning Process

Now, the right way. This process works for all Lowrance models, from the Hook series to the HDS and Elite lines. It takes about five minutes for a routine wipe and maybe fifteen for a deep clean.

Tools You Need (and Why)

  • Microfiber cloth — the only thing that touches the screen. Use a clean one, ideally 70/30 polyester/polyamide blend for best results.
  • Ammonia-free screen cleaner — a dedicated electronics cleaner or the T-H Marine Wave Away. Water alone won’t cut through salt residue or grease.
  • Distilled water — for rinsing if you prefer a DIY solution. Tap water leaves mineral deposits.
  • Soft brush or cotton swab — for the bezel and buttons where grime accumulates.

The 5-Minute Daily Wipe

After each trip, do this before you store the boat. It prevents salt from eating into the coating.

  1. Turn off the unit and let it cool down. Cleaning a hot screen can cause streaks.
  2. Spray the cleaner onto the microfiber cloth, not directly onto the screen. You want the cloth damp, not dripping.
  3. Wipe the screen in a gentle circular motion, starting from the center and moving outward. Use light pressure — you’re removing residue, not scrubbing off a stain.
  4. For stubborn spots like dried salt or bird droppings, hold the damp cloth on the spot for a few seconds to soften it, then wipe again.
  5. Dry the screen with a clean part of the cloth to remove any remaining moisture.

That’s it. If you do this after every outing, you’ll rarely need a deep clean.

The Deep-Clean Routine for Stubborn Grime

If you’ve let things go for a few weeks, or you’ve got a layer of sunscreen and bug spray mixed with salt, you need a deeper approach.

  1. Mix a solution of 50% distilled water and 50% white vinegar (or use a dedicated ammonia-free cleaner).
  2. Dampen your microfiber cloth with the solution. Wring it out well — you want it barely damp.
  3. Lay the cloth over the screen and let it sit for about 30 seconds. This loosens the grime without you having to rub.
  4. Wipe in slow, overlapping circles. Flip the cloth frequently so you’re always using a clean side.
  5. Pay attention to the edges and corners where grime collects. Use a cotton swab dipped in the solution to get into the seam between the screen and the bezel.
  6. Dry with a fresh microfiber cloth.

For the bezel and buttons, use a cotton swab or soft brush with the same solution. Don’t spray anything directly onto the unit — liquid can seep into the housing and damage the internals.

How to Fix a Scratched or Cloudy Screen

Light scratches and cloudiness are fixable, but you need to be careful. Deep gouges are not.

See also  Charleston Fish Finder - Which One Will Transform Your Fishing Game?

For light scratches, you can use a plastic polish like Novus #2 or a similar product designed for acrylic. Apply a small amount to a microfiber cloth and rub in a circular motion with moderate pressure. This works because the polish gently removes a microscopic layer of the coating, smoothing out the scratch. It won’t restore the anti-reflective coating, but it will make the scratch less visible.

For cloudiness — which is usually the anti-reflective coating wearing off — you have two options. You can leave it as is (it’s cosmetic, not functional), or you can remove the remaining coating entirely to make the screen uniform. Some owners do this with a plastic polish, but it’s a risky move. If you decide to try it, test on a small corner first and be prepared for a glossy screen that may glare more in sunlight.

Deep scratches are a different story. No amount of polishing will fix them. Your best bet is a screen protector, which can fill the scratch with its adhesive layer and make it less noticeable. It won’t be perfect, but it’s better than looking at a gouge all day.

Touchscreen Calibration After Cleaning

If you have a touchscreen Lowrance, you might notice that after a deep clean, the screen doesn’t respond exactly where you touch. That’s common — pressure and cleaning can throw off the calibration slightly.

Most Lowrance units have a calibration setting in the menu. Go to Settings > System > Calibration (the exact path varies by model). Follow the on-screen instructions to touch the crosshairs as they appear. Make sure your fingers are clean and dry before you start.

If your unit doesn’t have a calibration menu, a simple restart often fixes touch issues. Turn the unit off completely, wait 30 seconds, and turn it back on.

Preventing Future Buildup (Proactive Tips)

The best way to clean your Lowrance fish finder screen is to not have to clean it as often. A little prevention goes a long way.

  • Install a screen protector. A clear, anti-glare protector adds a sacrificial layer that takes the abuse instead of your screen. It’s cheap insurance and makes cleaning easier — you can wipe it with a bit more confidence.
  • Mount the unit where it’s shaded. Direct sunlight not only causes glare but also makes salt and grime dry faster, which makes them harder to remove. A sun cover or mounting location under a hardtop helps.
  • Use a rain-x style product on the screen. There are products specifically for marine electronics that repel water and make it bead up instead of drying into spots. Apply it after cleaning, and it lasts for weeks.
  • Keep a microfiber cloth in the boat. When you see a smudge, wipe it off immediately. The longer it sits, the harder it is to remove.

One thing I’ve learned the hard way: don’t use your regular boat towel. Those are often treated with fabric softeners or have picked up grit from the deck. A dedicated cloth for your electronics is worth the small hassle.

Seasonal Maintenance Checklist (Winterization & Spring Start)

If you store your boat for the winter, your Lowrance needs more than a quick wipe before it goes into storage.

See also  Which Fish Finder with Bluetooth and Night Vision Should You Choose?

Before Winter Storage

  1. Clean the screen thoroughly using the deep-clean method above.
  2. Remove the unit from the mount if possible. Store it indoors in a dry place where temperatures won’t drop below freezing. Extreme cold can damage the LCD.
  3. If you can’t remove it, cover it with a protective bag or a piece of soft cloth to keep dust and moisture off.
  4. Disconnect the power cable to prevent any trickle drain on your battery.

Spring Start-Up

  1. Inspect the screen for any new scratches or spots that developed during storage.
  2. Clean again with a microfiber cloth and ammonia-free cleaner.
  3. Check the bezel and buttons for any signs of corrosion or stuck debris.
  4. Power up the unit and test the touchscreen. If it’s unresponsive, recalibrate it.
  5. Apply a fresh coat of rain-x if you use it.

This routine takes about 20 minutes and prevents most issues that show up after months of sitting.

Frequently Asked Questions

Can I use Windex on my Lowrance fish finder?

No. Windex contains ammonia, which will strip the anti-reflective coating on your Lowrance screen. Over time, the screen becomes cloudy and harder to read. Use an ammonia-free cleaner specifically designed for electronics.

What’s the best cleaner for a Lowrance screen?

The safest option is a dedicated electronics cleaner that’s ammonia-free and alcohol-free. The T-H Marine Wave Away kit is a good choice because it’s formulated for sonar and GPS screens and includes a microfiber cloth. You can also use a 50/50 mix of distilled water and white vinegar if you prefer a DIY solution.

Can I use a paper towel if I’m careful?

Even if you’re careful, paper towels are abrasive and can leave micro-scratches. You won’t see them immediately, but they accumulate over time and make the screen look dull. A microfiber cloth is worth the few dollars it costs.

How do I get salt residue off the screen without scratching it?

Dampen a microfiber cloth with an ammonia-free cleaner or distilled water, then hold it on the salt spots for a few seconds to dissolve the salt before wiping. Don’t scrub — salt crystals are sharp and can scratch the glass if you rub them around.

My screen is cloudy even after cleaning. What’s wrong?

Cloudiness that doesn’t come off with cleaning is usually a sign that the anti-reflective coating is wearing off or has been damaged by harsh cleaners. You can try a plastic polish to even it out, but if it’s a deep haze, you may need to replace the screen or the unit. Prevention is the best cure.

What to Remember Next Time You Clean

  • Use only a clean microfiber cloth — never paper towels, rough rags, or your shirt.
  • Choose an ammonia-free, alcohol-free cleaner. The T-H Marine Wave Away kit checks both boxes.
  • Spray the cleaner on the cloth, not the screen, to avoid drips into the housing.
  • Wipe in gentle circles with light pressure. Let the solution do the work.
  • Clean after every trip to prevent salt and grime from building up.
  • Install a screen protector to add a sacrificial layer and make future cleaning easier.
  • Recalibrate the touchscreen after a deep clean if you notice any misalignment.

Affiliate Disclosure: We may earn a commission when you buy through links on this site, at no extra cost to you. This helps us keep testing products independently.

James

Written by James

James is a fishing enthusiast who shares his deep passion and knowledge through his blog. With a love for angling, he brings valuable insights and tips to his audience, helping them enhance their fishing skills and discover the joy of the sport.

Related posts

Leave a Reply

Your email address will not be published. Required fields are marked *